FishProfiles.com Message Forums

Dr,

I have to say that this is the sleekest design I have seen for any custom hood ever, very very lean. Love it!!!!

But, where exactly are the lights going? Into the part that flaps up? Will you add reflectors as well (you better, as I think you would loose loads of light otherwise )?

Ingo

---

Proud Member of the New Jersey Aquatic Gardeners Club

Now, if we weren't separated by sooo much ocean, I'd ask you to set up a little production factory in your basement & I'd buy 3 custom hoods from you. hehehe

Nah, you wouldn't, because I'm very expensive But really, this thing has become quite a lot pricier than I intended it to be. For the most part that is caused by the environment here in Finland, which is totally not geared towards DIY. Ten little M3 bolts, without the nuts, already cost about 4$ USD, I need about 30 of them just for the hinge I holland I probably could have gooten all need for just a few bucks. Oh well

Ingo, the lights will be installed with reflectors, so I'm not too worried about loss of light. Two 55 watts (50 cm each) T5 lamps go in the fixed part of the top (in the rear), then another two of those will be attached to the opening part of the lid, and I'm still considering whether I'll attach the current unit of two 38 watt T8 lamps in there, or just one of those. The current unit is rather unwieldy, and I may have to take it apart so I probably won't use it. I think I'll get ready for installing the lamps during this weekend, or the next weekend at the latest. It has to be finished by next weekend, as the weekend after that my parents are flying over and the appartment has to be squeeky clean by then, wife's orders

after that my parents are flying over and the appartment has to be squeeky clean by then, wife's orders

Sounds familiar to me, wonder where I have heard such orders before? Ah, that's right, at home

Anyway, your hood being so sleek, how far above the water column would the foremost units be? Seems like they would almost be in the water. Also, will there be a glass top above the water?

Ingo

---

Proud Member of the New Jersey Aquatic Gardeners Club

Anyway, your hood being so sleek, how far above the water column would the foremost units be? Seems like they would almost be in the water. Also, will there be a glass top above the water?

Ah, actually, it'll be quite a goodly distance. The part that I'm building is somethhing that I'm adding to the existing structure. Here's an old photo of the entire tank (from when I just planted it, two years ago).


As you can see here, the hood consists of just a 7 cm high "wooden" structure (which is made of plastic). This canopy is covered by the light unit and two plastic flaps that can be opened, one in the back and one in the front. The part that I'm building right now is to replace the current light unit. It will basically sink about half a cm into the "wood" that you can see here. The "wood" itself is glued to the glass and I don't dare remove it (especially with a filled tank), so I'm just adding a little on top.

Nearly done!

I spent about 7 hours on the new hood today and my back is killing me for it, but I think it was worth it. Most of the work today was measuring, drilling, fitting, measuring some more, taking apart, drilling, fitting, more measuring, etc

Right now I'm at the stage where everything has been fitted into the new setting and seems to work, only the final touches are still required to make everything look good. It'll probably take me another two hours tomorrow evening to get that done.

Two things that will take a bit more work:
- fabricating,measuring, fitting and drilling two corner profiles to support the lid at the sides, near the hinges. I thought I wouldn't need those, but I've noticed that without them there is a bit too much movement, and opening the lid will give too much stress on the rear bolts. If I don't make those, I fear that it'll casue the perspex to break in the back after some time.
- reversing the ventilators at the back and installing the regulator for adjusting the fan speed. I tested them today, and found out that the fans are now blowing air out of the hood... I think I'll get better cooling if I actively blow cool air into the hood. I already have the fan regulator and it works nicely, except for the problem that it only has one connection for a single fan, I'm going to splice the wiring so it'll take two fans instead. all in all it shouldn't take much more than 15 minutes or so.

Here's then some pictures, I found the oríginals not very clear so I've photoshopped the lights and airflow in there. Enjoy.

PS: As you can see, my most trusted adviser keeps a close eye on my workmanship

All seems to be going well with the new hood. I'm so glad you have a wise & trusted advisor, ensuring you do no wrong.

Cheers
TW

Dr.,

A cat is your adviser? Be careful that the finished product is not some form of fish trap that provides a snack

Anyway, I looked at the pictures before reading the words, one shouldn't do if one is to avoid unnecessairy questions, like "that are some skinny bulbs there", . Nice photoshop work.

And overall, seems to come together really nicely.

Ingo

---

Proud Member of the New Jersey Aquatic Gardeners Club

A cat is your adviser? Be careful that the finished product is not some form of fish trap that provides a snack

Good point, I didn't quite consider that, but unless she suddenly learns to lift heavy stuff I think it'll be alright

It is done, it still took several hours of fiddling and it looks like I still need to make a few minor adjustments (somehow the lid seems to be 2½ mm off to one side... and yes, I'm a perfectionist when it comes to this ), BUT... it works, it fits, it is silent and it looks pretty!

I won't talk much, it's late, I'm tired and I still have to clean up the mess, so I'll leave you with three photos: the first one is the old situation, with the "original" system where I added the two noisy fans to keep things cool. All the stripes are pieces of double sided tape I put on top to keep the cats from sleeping on the hood (and no, it didn't really work... spraying with water did).



Then this is the one you've been waiting for:


I just realized that this angle may not be the best, maybe I'll take another photo tomorrow.

Finally, the lid open. When I first did that I was kind of stunned myself, I can reach the ENTIRE surface of the water and still have light in the tank, which will make working in it so much easier.



For this one also the angle may not be the best, I'll see if I can get some better shots tomorrow.

In any case, enjoy and feel envy

Looking very sharp and shiny, Dr.

Good job on getting it all together, but you have to work on the two mm,

Anway, yeah - having lights on the tank and being able to reach all areas inside the tank is a great thing. I have this on all my tanks when I remove the glass cover but keep the elevated unit in place.

Have a good sleep,

Ingo

---

Proud Member of the New Jersey Aquatic Gardeners Club

Wow, that looks great Dr. Bonke. I would love one of those myself. Gotta love all that room to be able to mess with the tank without having to lift a fixture off the tank every time. I wish I'd have thought of that for my SW fixture. I have a feeling that I'm going to be making that one over again. I'll probably stay away from the plastic, but I might steal that hinge idea.

---

Critical Fertilator: The Micromanager of Macronutrients

Very Impressive, very sleek. One Issue with for example the coralife fixtures over a glass top is that the light shines on the glass top which highlights the dust and other smudges on the glass. When the light is completely contained inside the hood (as it is with your unit) the light only shines into the tank.



My Scapes

Impressive job. Let us know when 2mm has been taken care of

Cheers
TW

Today was a day off so I actually had some extra time to do a bit of work in the tank. A bit of trimming, waterchanges, etc. All in all I'm quite pleased though the stargrass looks rather thin atm due to the cutting. I cut away the tops and left the bottom parts in as an experiment to see if it'll slow down growth a bit or not (replanted tops reach the surface within a week since I started fertalizing with Nitrate again). Other news is that I've finally received the glass covering for the tank, evaporation issues should be covered now.

Anyway, I've taken some photos of the tank(s) after today's waterchange. Enjoy.

PS, the 2 mm still needs to be taken care off, it involves remving the whole hood and widening some of the drilling holes on top. Right now I just cant be bothered with it
.

first some whole tank shots:
20.10.06: Just over a month ago, before I changed the hood


30.11.06: A month later, new hood is installed and I've started dosing with nitrate again (before I dosed only with micros and a bit of phosphate


06-12-06: Today, right after a water change. Note that the increased amount of Nitrate causes quite a different color in the sunset hygro, instead of the deep pink, it's now a light rose.


Some other shots, first the bucnh of greedy tigerbarbs... these guys are ALWAYS hungry, and when they get food they eat so fast that almost every time a few of them swallow a lot of air and have major buoyancy problems after dinner:


A detail shot of the tiger lotus, it was tiny a few weeks ago, but it has grown a lot in the last two weeks and produces a new leaf every few days. I even managed to catch a couple of rummies in this shot:


Finally a shot of the other tank, I recently installed some new lamps and reflectors, since then plants are actually showing some growth again... next year I may get a similar T5 lighting system for that tank, it's just a little too dark for my liking.


Oh, and tomorrow I may actually be getting my tenth gold star.... if I don't break down in nerves that is

Man! That is unreal! Only in my dreams I will have that!

Guess it just goes to show what knowledge, planning, hard work & determination can achieve!

its beautiful.



wow.

GFG

_______________________________________
Never be bullied into silence. Never allow yourself to be made a victim. Accept no one's definition of your life; define yourself.
Harvey S. Firestone

Simply beautiful. I'll interested to hear if cutting from the top slows down the stem growth. I'm growing weary of pulling out the stems each week for trimming - yes they reach the top in a week, same as yours.

BTW, you must get to work on that 2mm

Cheers
TW

Very nice colors, the stargrass looks exceptionally healthy. I have a love/hate relationship with that plant in my tank and I keep reducing it's presence due to the maintenance involved. Cutting the tops might buy you alittle extra time, but probably not much.

I also have a recently acquired tiger lotus and it's growing new leaves quite rapidly. I'm told if a leaf makes it to the surface the plant will die.

My Scapes

I also have a recently acquired tiger lotus and it's growing new leaves quite rapidly. I'm told if a leaf makes it to the surface the plant will die.

Nah, that's nonsense. The plant is just like a regular lilly and will keep on making new leaves, but they will then all go to the surface. At that point it will become harder to induce it to make the immersed leaves. So in general, as soon as you start seeing a leaf going to the surface, snip it off close to the bulb. Most of the time the next leaf will be immersed again.

Very nice colors,

I also agree with Tetra on the colors. I must be running way too high of Nitrates in my high tech for my sunset to color up. It is almost always bright green.

In my 29G most of the stems are either pink or dark pink. In this tank I do hardly any dosing and I am running way less light (20W). The low nitrates must be the key to keeping this plant looking sharp.

What are you dosing for nitrates BTW?


55G Planted tank thread
19G Container Pond
[IMG]http://i4.photobucket.com/albums/y118/Wingsdlc/Ric

Very Nice Dr.,

I like the whole series of shots and each one of them shows a wonderful tank. You sure have a hand and eye for a good layout (albeit not Amano like ).

Also, I remember shots of your smaller tank being in really bad shape, all seems to have turned for the better there as well.

Ingo

PS: AND STILL NO 10TH STAR?????

---

Proud Member of the New Jersey Aquatic Gardeners Club

Thanks for all the supporting comments and praise Much appreciated, though I wouldn't mind some suggestions either (some, mind you! )

What are you dosing for nitrates BTW?

I have a stock solution of 200 mg/ml KNO3 of which I dose 5 ml twice a week. I'm still not sure if it helps, but I've started dosing in the evenings, with in the back of my mind that the plants then can use the first wave during the night and then get a bit of a headstart over algea, which won't do much during night time. But that's just a theory which isn't really based on actual data, I just read somewhere at some point that plants do most of their growing during night time and hence my theory.

albeit not Amano like

Yeah well... maybe some day
And the small tank is indeed doing a bit better, I think in part it had to do with the plants having to get used to low light and also lack of maintenance from my part. It doesn't take much to keep it the way it is now, as it's lowlight, non-CO2, so the plants grow really slow. But the waterchanges are still kinda necessary in order to keep cyanos away.

PS: AND STILL NO 10TH STAR?????

Like I said, maybe later today I keep on messing up on a couple particular questions, I think I've made the same stupid mistakes several times, for example: what kind of filtering is filter wool? I think I've answered "biological filtering" many times while the correct answer (according to the quiz) is mechanical filtering. I have been told on several occasions that the filter wool's main purpose was to create a surface for beneficial bacteria, that it also catches some of the larger debris was an added value. but now that I finally know the answer to that one, I think I can get that one right

I have been told on several occasions that the filter wool's main purpose was to create a surface for beneficial bacteria

I can see where this is true, and false:

1) Every surface is good for beneficial bacteria, inside and outside of the tank, as long as the tankwater flows by.
2) Filter wool would be no exception
3) But - its overall surface area is actually rather limited to the individual strands of wool, and they are not packed realy dense. Other media offer on the same volume occupied a much larger surface.
4) Also, this gap between the individual strands is sooooo large that loads of water will flow by without ever hitting them. Larger particules, usually debris and such, are too big for these gaps and get stuck.

Makes sense?

Ingo

---

Proud Member of the New Jersey Aquatic Gardeners Club

I have a stock solution of 200 mg/ml KNO3 of which I dose 5 ml twice a week.

What does that work out to be in PPM? I don't know how much water you are mixing it into.

55G Planted tank thread
19G Container Pond
[IMG]http://i4.photobucket.com/albums/y118/Wingsdlc/Ric

Congrats on the 10th Star Dr.



Ingo

---

Proud Member of the New Jersey Aquatic Gardeners Club

Ingo, it does make sense in a way, though I have to add that I've always packed my filterwool rather tightly to increase the exposed surface on which bacteria can grow. I always looked at if from the perspective that a wool thread has 360 degree exposed surface area and as there are very many threads the total amount of exposed surface would be bigger than that of larger filter material. But then again, there is an awful lot of open space even in tightly packed filter wool, so I’m probably wrong on that.

In any case, I think I just got my tenth star right before making this post (was it now so that in order to keep them you need to redo the test every two weeks?)

Wings, according to Chucks calculator I add 2.8 ppm with each 5 ml. The amount of water in my tank is a bit of an open question, the tank basically is a 65g tank, but with the background, substrate, etc. I guess it's more like 55-58g.

(was it now so that in order to keep them you need to redo the test every two weeks?)

No, once you got them you will get the badge and that's it, all done. I hope they will never change that as I believe we all worked hard enough to get there (given that I am not getting paid for it).

And it must have been a little earlier that you got the star as I already congratulated you on it on the last page

Ingo

---

Proud Member of the New Jersey Aquatic Gardeners Club

Hi,
When I was using HOB filters 5 decades ago, we used "filter
floss" and we were told that you wanted to put enough in
to do the job, but not to cram it in as it would clog and
back up the filter to the point where it would over flow.
The carbon was supposed to be placed on top of the filter
floss with the floss the last part of the filter before the
water was returned to the tank. That made the charcoal
serve two purposes, mechanical and chemical filtration.

One would watch the filter to see if the water rose inside
the box and would change the whole mess before it over
flowed the box onto the floor. Eventually, given your
individual tank, you would learn that you had to change
the filter every X amount of time and it became a part of
your aquarium maintenance. I would use about an inch of
floss with about 3 inches of charcoal above it.

Frank


-->>> The Confidence of Amateurs, is the Envy of Professionals <<<--

So you are using 5ml of Nitrate 2x a week. That is giving you 5.6 ppm for the whole week. Right now I am giving mine 11 ppm 3x a week. Needless to say I am running my Nitrates way higher than you. I guess that is why I am not getting the color out of my Sunset.

Thanks for the info.

55G Planted tank thread
19G Container Pond
[IMG]http://i4.photobucket.com/albums/y118/Wingsdlc/Ric

It's been a very long time since I last posted anything on these forums, and even longer since I last updated this thread.

In the 2½ years since the last post I've been busy with all sorts of things and nearly broke down the big tank as it was giving me so much algae grief. After getting rid of the angelfish that were eating my plants, I decided to rescape the tank and clean it out properly. I suppose the cleaning wasn't fully completed, as I ended up with a big BGA problem, which after about a month turned into a huge bright green hair algae infestation. I as was traveling out of the country a lot during that time the tank was going through a lot of swings, I'd remove the algae, dose ferts for a while and then would be away for two weeks and find it completely filled with the green stuff. I'd never seen anything like it before, the strands were so long you could problably spin algae wool out of it. At the time there were no fish in the tank, I re-housed them all into the smaller tank I have.

In short, the tank looked awful, the plants miserable, and I was just not enjoying to look at it. By then I had also ran out of CO2, the lights were not working too well anymore, and had issues with the filter. To give you an idea of what it had turned into by then:


Then around February this year my schedule started to open up a bit and I managed to refill my CO2 bottle, I got a solenoid valve installed to turn off CO2 during the night time. I ordered new lamps and got the filter working reasonably well (I'll probably still buy a new one soon). I also started doing daily maintenance, every day I would spend about 10 to 15 minutes removing any hair algae that I could see. I dosed ferts only minimally, plant growth had been minimal for nearly a year, and I wanted to start off slowly.

It seemed to work, after about a week under the new regime, most stem plants had very bright new tops, and the cryptocorynes were forming some new leaves.

Here's a picture of about three weeks into the recovery, at April 12

Most notable is the Alternanthera, which was almost completely gone. Also the Lobelia cardinalis is slowly recovering in the lower left corner.

Another two weeks later growth had really kicked back in, below is a rather poor quality photo of the tank (it's a cutout from a larger photo depicting our living room).


By then I also had some fish in the tank again. Currently, there is two flying foxes, two pearl gouramis, 3 young Botia histronica, and 10 Harlequin Rasboras. Of one of the harlequins I managed to get a decent shot with the new digital camera.



This week I finally got the feeling that most plants were recovered enough to start reshaping the layout a bit, and as a result the water was too cloudy to make a good shot of the tank, but I'll make one tomorrow and upload it.

Whether I'll keep updating this thread regularly still remains to be see. I've said several times that I wouldm and it always fades out after a while, but time will tell .

Best,
Martin

Doc - The tank is looking pretty good again. The plants for sure seem healthy. I think that a planted tank is hard to keep up when you don't have time to put into it. equipment issues only make things worse.

I just moved and rescaped my 55G if you want to come check it out.

55G Planted tank thread
19G Container Pond
[IMG]http://i4.photobucket.com/albums/y118/Wingsdlc/Ric

I just went through and read all ten pages of your diary!

WOW your tank had an excellent start and many, MANY trials and tribulations throughout its growth and I honestly am glad you stuck with it as many times when a tank gives me that much grief I tear it down and start over. I must give you some props for sticking with it and still ending up with a brilliant tank!

you have done an amazing job, keep up with it, and keep us posted on how it is doing... there is nothing more rewarding than keeping an ecosystem stable and being rewarded with fry and the constant growth of plants.

-Brandon

\\\\\\\"an ounce of prevention is worth a pound of the cure\\\\\\\"

Thanks for the kind comments. The only reason I never tore it down completely to start over was that I knew I would not have the time to keep up the maintenance after restarting, and I figured it would just be a waste of time, money, and effort. When we would get visitors I would spend an hour or two removing the worst of the algae and then basically try to avoid talking about the tank until they would leave

Yesterday I did some small maintenance and cleaned out the filter. By now the water is reasonably clear again (just a hint of cloudiness left) and I figured I could take a proper shot of the tank to show what it looks like right now. Here is the same shot from April 12 (last month) and then the one from 10 minutes ago (May 18).





What a difference one month makes, huh? I should add here that only once new plant was introduced during this time, a Anubias barteri, in the right back corner to hide my CO2 distributer (an old power head from a crappy filter I got with my small tank).

The Bacopa has recovered incredibly well, for nearly a year it pretty much did not grow at all, the tips were all thin with very small leaves, and it was making a lot of tiny purple flowers. The flowers were somewhat concerning, as plants make them either when the conditions are really good, or as a final resort when conditions are so bad that the plant is likely to die and only seeds seem to be a possible way to continue. I was pretty sure my conditions were far from optimal, so I figured the Bacopa was about to kick the bucket. By now the leaves from some stems are bigger than I've EVER seen on Bacopa, and the color is really quite pretty.

Since a month ago, also the crypts all have made wondrous recoveries and a couple of tiger lotuses have popped up. The only plant that is doing so so is the Alternanthera, some stems look very good, others have very curly leaves. I think that's a sign of some deficiency, but I'll have to look that up.

Wow Dr. Bonke, looking great! I'm enjoying the bacopa tood. I don't see it used very often, and yours is showing a lot of color up top.

---

Critical Fertilator: The Micromanager of Macronutrients

Wow! Great to have you back posting again Doc!
Missed Ya!

The tank looks great.

CUL,
Frank


-->>> The Confidence of Amateurs, is the Envy of Professionals <<<--

The only plant that is doing so so is the Alternanthera, some stems look very good, others have very curly leaves.

Alternathera seems to be that way. I can't quite put my finger on it either as some of mine look great and others right next door do not. I am pretty sure I am not low on nutrients either as I am dosing EI.

55G Planted tank thread
19G Container Pond
[IMG]http://i4.photobucket.com/albums/y118/Wingsdlc/Ric

Wow Dr. Bonke, looking great! I'm enjoying the bacopa too. I don't see it used very often, and yours is showing a lot of color up top.

It's one of my favourite plants these days, also when you trim the plants, they give quite a nice smell. Sometimes I wonder how they would taste in a salad

Alternathera seems to be that way. I can't quite put my finger on it either as some of mine look great and others right next door do not. I am pretty sure I am not low on nutrients either as I am dosing EI.

I just read that it may have something to do with high light, some people seem to have some trouble with growing it under high light conditions, and during the peak hours of the day I have about 300 watts of light over the tank (6 55W T5 lamps), and some of the better looking stems are a bit shaded by other plants. I'm going to keep my eyes out for some different red plants, or perhaps once the Limnophila aromatica grows out a bit more I'll use that to fill in those spots. Right now the number of plant species is a bit high, and although the different sections look very nice up close, I do find that the overall look is a bit messy in these photos. I'll be traveling the next couple of days, so I'll hope the tank lasts alright until Sunday. I may make some fertilizer batches for my inlaws to add while I'm gone.

Two weeks since the last entry. Not terribly much has changed and the tank lived through my 4 day absence quite well. I added some extra fertilization before I left and that resulted in some crazy amount of growth on the first couple of days. However, it seems that by the third day the plants ran out of nutrients. The Lymnophila is the best indicator, it got some really big leaves during my absence, but then the growth tips just all collapsed. By now most look as if someone cut off the tips and they are making new shoots at the end. Here are some shots of the tank, one whole view, and a couple of more detailed shots.



Here you can see some of the recovering tiger lotus, they're still small, but making leaves rather quickly. Keeping them in check once they get bigger may be a challenge


A close-up of the Anubias in the back, it actually is making a flower, that's the first time in the life of this tank that an Anubias is actually producing one. Just above and to the right you can see the outlet of the powerhead that mixes the CO2 into the water.


Finally a shot of the left side of the tank, here you can see the tips of the lymnophila that suffered (probably due to lack of nutrients).

Doc - The tank sure is looking great! The plants are much more full and green.

I wish you the best of luck with the lotus. I have a dwarf lily in my tank right now. It started as a bulb with one or two very small leaves. I came back from a week of vacation and it had 10+ leaves that were 4-6 inches in diameter. I took the mother plant and put it in my outdoor tub and left a small baby plant.

55G Planted tank thread
19G Container Pond
[IMG]http://i4.photobucket.com/albums/y118/Wingsdlc/Ric

Long time no see. based on the limited amount of new posts since my last login I doubt there many people hanging around anymore, but I figured I could leave a message.

My tank has been up and running pretty much continuously for the last 8 years but had a major overhaul in the spring of this year (after a two year limited attention period). Since then I've been battling with all the kinds of algae you can think of, but now finally have sorted them all out.

The tank is fully high tech atm: pressurized CO2, pH measuring, EI fertilizing, and chemical balancing of the hardness of the water. Earlier this week I did another minor overhaul, added some new driftwood and got rid of most of the leftover BBA. The plants still need to do some filling in, but overall it's now slowly moving into the right direction.

here's the tank as it looked like earlier today:

Hi Doc!
Great to hear from you again, and truly a striking tank!
What are those fish? They are a really nice shade of lavender.

Like you, life gets in the way of play. I've retired for the third time and living full time in our home at 10,000ft elevation inside the Colorado Rocky Mountains. Susan is going through kidney failure (rejecting her second transplant, and we are in the process of building an addition to the house. With all that is going on and demanding my attention, I'm beginning to wonder what real retirement is like!

Frank

-->>> The Confidence of Amateurs, is the Envy of Professionals <<<--

Wow Frank, sorry to hear Susan is having so much trouble. I've seen what kidney failure can be like with my grandfather who needed dialysis twice a week. It always took him two days to recover from that. I hope things will work out for you so you can actually enjoy the retirement.

As for the tank, the fish are Congo Tetras, with the Grolux lights their amazing color comes out beautifully.

The tank is doing well, algae seems mostly a thing of the past and I only have to clean the glass a little once a week at the water change. The plants seem to stay totally clean of algae, only the wood and background gain a bit of color, which I actually don't mind so much.

As the tank has developed quite a bit over the past year, I figured it would be nice to add some progression pictures.

In February last year I restarted the tank after I lost 90% of my fish in a severe Ich attack following the introduction of some marbled hatchet fish.


Two weeks later the surviving fish were introduced:



Then came our trip three week trip to China, during which the CO2 ran out and my parents in law "took care" of the tank (i.e. fed the fish):


The algae problem was quite overwhelming, especially with little time on my hands due to learning how to be a good father, yet, slowly things got a little better:


and a little better still, May 26, 2012:


In June, the green hair algae was losing big time:



In July, the green hair algae was a thing of the past, but I was still fighting some staghorn, green dust algae, and black beard algae was beginning to be a problem:


During August, we were again away for vacations, and on return the black beard algae had covered almost everything except the very new parts of the plants. I began spot treatment with peroxide and got rid of my CO2 reactor, instead using a powerhead for CO2 injection. From that point on things slowly got better:


In November I did a slight rescape, removing some old wood, and adding a new piece:


On January 4th, most of the old, algae covered plant parts are now gone, and some modifications of plant positioning were done.


And as of today it is mostly a matter of plants growing into their proper positions and volume.


Things I did to get rid of the different algae issues I have had over the past year:
Green hair algae: reduce photoperiod to about 9 hours, increase CO2 and lowering amount of ferts (I use EI).
Green water: yes, I had some of that too. I installed a UV lamp
Staghorn: adjusted the amount of phosphate fertilizer.
Black beard algae: removed the apparently inefficient CO2 reactor and got a powerhead instead (see right side of the tank). Increased CO2 to about 4 bubbles per second. In addition I treated the tank on a weekly dose with Flourish Excel.

There you have it.

HI Doc!
"Learning to be a good father." CONGRATULATIONS!!

Replacing the reactor with a power head... is this a powerhead that as a reactor built into it, or, are you just plugging the CO2 line into the fitting that is mounted on the top of many powerheads where one attaches an air hose to it so it pulls atmospheric air into it and sprays out small bubbles, and in this case it sprays out tiny CO2 bubbles?

Frank

-->>> The Confidence of Amateurs, is the Envy of Professionals <<<--

Frank, thanks so much. The trip to China I had early last year that led to my tank being bright green on my return, was to adopt our son Daniel. He'll be two next week and is aboslutely fantastic.

As for the powerhead, it's a cheap one from ebay that has a barred intake at the bottom. I removed one of the bars and simply feed the CO2 hose into it. The bubbles are very fine and the pump is relatively strong, so by the time the bubbles get close to the surface, they meet the downwards current from my external filter on the other end. While CO2 is active, my tank almost looks slightly misty fom all the tiny bubbles (both CO2 and the oxygen produced by the plants).

The tank looks best late in the evening as CO2is off from one hour before lights go out.

Dr. Bonke congrats on the adoption
It's a 10 year waiting list here!

Even with the algae that's a stunning tank (geez those congos look great!).

Thanks for the notes and photos.

^_^

Thanks Babel,

If I learned one thing over the past year it is how to deal with different kinds of algae

By updating this thread I hoped to do my small part in reviving the site a little, but if I'm totally honest I fear it is mostly falling on blind eyes. There really isn't much activity here anymore. As seems the case with most forums these days. I'm getting the feeling that forums are slowly becoming a thing of the past while the world moves on to different/faster social media.

I still mostly lurk around here. I recently(ish) joined my local aquarium club, which has been awesome. They have a forum too, which is great to discuss fish stuff with people who have the same water, LFSes, and can trade with more easily. I expect to stick around here too though, for things like this

><>

Congrats on Fatherhood ! Also your tank is looking sweet. Still have the eye for plant placement too I see

The Amazon Nut...

Thanks guys

This will likely be the last update for this setup of my tank. In three weeks from now I'll be moving house and will have to tear down the whole thing. I hope I won't suffer too many losses in life stock, but I'm fairly sure I'll be losing about 80% of my plants as they will need to be need to be transferred to a smaller tank for a couple of weeks, which has different lights. As the weeks following the move will be quite busy, I doubt I'll have the time to set up this tank any time soon.

It's a shame, as it has now really settled in nicely. Plants grow very well, and with the exception of a bit of green spot algae on older leaves and some random BBA on the wood, I don't have any trouble with algae at all.

Have a look at the final iterations. Here is the tank on the 28th of January, right before a major trimming:


And as of last night, just before lights-off:


I thought that after I added Congo tetras nearly a year ago, I would not see any young fry make it to adulthood anymore, but currently I have four nearly adult Black mollies that survived, and there's at least five growing sword-tails among the plants, which I expect will survive.

Stunning and sad

No one you know of that could plant-sit for you that's got the right type of tank setup?


Good luck with the move, hope all goes smoothly.


^_^

Hi Doc,
I hope the move goes well and that you can soon return
to your tanks.
Moving, even for happy occassions, is still, never fun.

Uprooting, and packing and dislocation are not necessarily "fun" words.
Hope all goes well...
Frank

-->>> The Confidence of Amateurs, is the Envy of Professionals <<<--

Babel, I'll be setting up my old 80 cm tank at the office for the moving period. Tomorrow I'll do the preparations for that. However, I haven't really tested the light for that one yet (the old fixture broke down some years ago), so it remains to be seen how well the plants will do in there. Also, the bioload will be quite heavy in that tank, considering that I already feel as if I'm somewhat overstocked in my 120 cm tank. But we'll see what happens.

For my main tank it will take a few weeks at least before I'll have the time to set it up, April is likely to be the earliest I'll have time for it. I'm planning to rip the old foam background out. It's now been in there for about 9 years and I've come to realize that I made it too thick and too out of place. The only real use I've had of it over a plastic cover on the outside is that it holds some anubias plants in place. Most of the time I can't actually see much of it at all. It's time to get that out and get all the space it occupies (5-7 cm) back.

Frank, I'm actually kind of looking forward to the move, ever since we decided to look for a new place, I have started noticing more and more little things that annoy me about our current apartment We'll actually have our own free standing house now, instead of a second floor 5-room apartment. Lots more space, no noisy neighbors and a big garden. We're very much looking forward to it.

Sounds like a good move to me, just a shame to have to tear down the tank but you will get to start over, with more room all around so I like it!
Plus now you'll have a garden to water with all your WC water.

Couldn't you use the 120 light fixture on the 80? It'll hang over a bit but at least you know it's functioning properly.

^_^

Sounds like you'll have it pretty good in your new home, but a shame you'll have to tear down the tank when it looks so gorgeous!

><>

I still lurk, occasionally. I mention fishprofiles whenever someone (at work) mentions a pond or aquaria at work. Frank, you are my U.S. point man on the site. So don't get mad if you get a few questions.

TTFN --->Ta-Ta-For-Now
Kelly ;o}

Hi Kelly,
I hope that everything is going well for you and your family. Miss the times in chat.

Winter is still holding on.. it was -2 this morning but with the cloudless sky, we are up to 17 now and the snow is melting. We have had, sometimes, two storm cells in a week passing by leaving 3-8 inches of snow with each. Down in the "flatlands" the spring flowers are starting to push through the soil. Here at 10,000 feet, the aspin trees are just starting to bud, so perhaps in a few weeks, spring will make itself known.
Meanwhile.. Welcome to Springtime in the Rockies!

Frank


-->>> The Confidence of Amateurs, is the Envy of Professionals <<<--

Same ole thing here in Michigan. We had 80 degree weather Thursday. Then a storm front rolled thru with horrible winds and the temp dropped over 30 degrees, in one day! It snowed the following day. I want Spring back!

In Michigan, if you wait 10 seconds the weather will change.

TTFN --->Ta-Ta-For-Now
Kelly ;o}

How did your move go ? I hope smoothly. Totally understand the challenges of an apartment, a house would be sweet.

The Amazon Nut...

The move itself went pretty good, but my main tank is still standing empty. After getting most of the house in order and having bought new white furniture, I painted some old furniture similarly glossy white. This turned out so good that I decided to paint the aquarium stand and frame white as well. So far though I haven't had the time for that, so it's standing empty here in the living room. I'll probably do the painting in the next few weeks as I'm now on holiday. After that it'll be coming up with the new layout and getting all the necessary plants and such. I may revive this journal at that point to show the intermediate steps.

have a nice summer all of you!

Hi Doc,
After viewing your "old" tank, we are all awaiting pictures of the new one as it evolves.

Frank

-->>> The Confidence of Amateurs, is the Envy of Professionals <<<--

The tank is about to go into revival mode. I've finished with spray painting the stand and the "wooden parts" (plastic) of the tank. It's now all high gloss white and came out very nice. I've also replaced the styrofoam background with a simple black foil that is stuck on the outside behind the glass.

Two days ago I ordered the new substrate from Germany, despite the high shipping costs it's still a lot cheaper than buying it here locally in Finland. I guess the market here is smaller, but a 50% difference in price seems a bit excessive and although I wouldn't mind supporting my local LFS, I'm not stupid (nor rich) either. Today I got the message it's all shipped, so I expect arrival early next week.

One thing Finland does have a lot of, and free as well, is rock. The whole country is basically granite and whenever new buildings are being built the constructors blow up huge chucks with dynamite. The interesting bit here is that these explosions leave interestingly shaped smaller pieces which normally just get loaded up and get disposed somewhere. I've found a site where I guess the money ran out, and it's been lying bare for quite a long time. A quick walk through left me with 20 kg of rock and after sorting through those, I think I'll go back another time to have a second look.

In any case, I expect to be able to start scaping next week and I'm very much looking forward to it. I think I'll keep it this time mostly to relatively low maintenance plans (i.e. very few stem plants) but right now I'm still not entirely sure. I'll post the updates once they come in.

Hi Doc,
Granite is a plutonic igneous rock that is mostly two types of feldspar, and quartz with two types of mica thrown in. Here, we have some really nice pink granite and it is just laying around all over the place. When it is fractured by the explosions or by smashing it with a hammer it will generally cleave (fracture) at 90 degrees leaving some nice square or rectangular pieces.

Now I'm really getting interested in those pictures!

Frank


-->>> The Confidence of Amateurs, is the Envy of Professionals <<<--

Well then,

The tank is back up and running, for the most part anyway. Last week the new substrate arrived and I did the layout during the weekend. I'm still not 100% sold on it as it is, but for a large part I think it's also because it is still so bare. From My office tank I managed to rescue a few, very sorry looking plants and I got a few new pots form the LFS. My guess is that it will take a few weeks/months before it's properly filled in, I just hope I can balance the ferts right so algae won't take control. Right now I'm still missing CO2 (have to refill the tank, which will be done tomorrow) and I have a couple of new lamps waiting for me at the post office. After that it's down to water changes and fert management.

Just to give an idea what happened, here is a photo of quite a few years ago, when the stand was still its original wood color:



This is a week ago, after painting and cleaning. BTW, the silicone on the rear glass has proven extremely difficult to be removed. I'm never going to glue in a background again.


here it is nearly filling time, the basic layout is now done (though I'm seriously considering to get a couple of really big rocks and adjust this layout.
Substrate: first a layer of JBL AquaBasis plus, then a layer of JBL Manado, and finally JBL Sansibar Black on top. The withe isn the middle is JBL Sansibar White.


Here is the first planted version, the morning after the plants went in. It'll be some time before it is anywhere near satisfying.

Hi Doc,
Wonderful, "A river runs through it." This should be an interesting set of pictures as it fills in and you may some changes along the way.
Frank

PS, I think you photo shopped the cat in the picture!



-->>> The Confidence of Amateurs, is the Envy of Professionals <<<--

I like the name Frank, I may need to keep that.

A short update. I've had the CO2 cylinder refilled and set that up yesterday afternoon. In the evening I replaced three of the old lamps, and I hope this will give the plants a needed boost as the first beginnings of algae are starting to show. Since it's a fresh started tank I expect to be fighting algae for the first month or two, but I hope I can keep it to a minimum, as it always makes everything so unsightly.

About the CO2, I had a near disaster in the evening when I heard a crack during the installation of the new lamps. Pretty soon I saw water on the floor and my heart stopped for a second as I feared the glass had broken somewhere. Luckily it wasn’t anything that bad. As it turned out, the plastic lid of the bubble counter I had installed earlier in the day had cracked. That counter has been running happily for quite a few years, but had been dry since the move, my guess is the plastic got brittle and could not handle the new pressure. Whatever the case, I removed the thing and caught the crack in time. If that had happened during the night, I would probably have ended with 20 odd gallons of water on the floor. So I’m quite happy it went the way it did.

It's been a while.

Life's been busy, we adopted a second child and with all the extra work that comes with that the tank has been given a lot less attention. My CO2 tank ran empty about a year and a half ago and as it then needed to be pressure checked I decided to move to a lower maintenance setup. The new (led) light fixture I bought some time ago has a half light mode, so that only runs half the leds it normally would do, and my grolux T5 I only have on for a couple of hours in the evening.

It did mean that a lot of the plants slowly died off as their light requirements simply weren't met, but the added benefit was that I no longer had to struggle against algae. There are now a couple of species of javafern, cryptocoryne and bolbitus in the tank and I find it looks surprisingly pleasing. It also saves me on energy cost, the bills for CO2 every 3 months or so and the maintenance is super easy.

Attached Image:

Really nice to see an update, tank looks great!

~~~~~~~~~~~~
There is water at the bottom of the ocean

This site seems to have gone to sleep, so I'll do my part to give it a tiny nudge. Here's my tank as of last night after a little trim. It is still very low tech, as the CO2 cylinder still hasn't been pressure-checked, but the current set of plants don't seem to mind too much.

Attached Image: